I moved a 7911 (using SCCP) from one cluster to the next. I did a factory reset and tried to connect it to the new cluster, and now it will only download the SIP firmware. I went as far as setting the SIP default load to that of the SCCP, and it is still using the SIP Firmware. I have a cisco 7911g phone to be converted from skinny to SIP. I have the downloaded firmware with me (version 9.2.1) and followed the exact same steps as above. The phone boots and I am getting the below tftp log “Serving term06.default.loads” to 192.168.1.201″ where 192.168.1.201 is my cisco 7911g.

I have a problem with 7911 IP phone. I have installed 2 new 7911 IP phones and registered it on UCM 8.6.2. The office season 6 buy.

They have successfully registered but the confugured locale have not been applied. I've done factory reset by 123456789*0# combination, the phone began repeatedly reboot with several minutes interval, showed upgrade screen for several seconds and than showing a Cisco logo with 1 circle with dot in lower left edge on the screen. I've reset it with *# after that I see a clear screen and the phone flashed its transparent buttons with several minutes interval. In tcpdump I see the phone loads term11.default.loads, UCM sends it and than no activity from the phone. In term11.default.loads I see the following: Trozkiy:~ mdenisov$ strings./term11.default.loads 'CN=someSigner;OU=someOrgUnit;O=someOrg #CN=someCA;OU=someOrgUnit;O=someOrg O78m wtmckTd a]=I 72Xxl term11.default.loads # This file contains a list of archive image files that will be requested by the # RELEASE load version 9-2-1TH1-13 #HARDWARE_COMP_1 1 jar11sip.9-2-1TH1-13.sbn cnu11.9-2-1TH1-13.sbn apps11.9-2-1TH1-13.sbn dsp11.9-2-1TH1-13.sbn cvm11sip.9-2-1TH1-13.sbn Trozkiy:~ mdenisov$ The phone should be SCCP. How can I troubleshoot thes problem? I have set build all cnf files in service parameters and restarted tftp service.

Other phones can register and upgrade successfully. Is there a way to connect to the phone with telnet, ssh or something else end see what do it needs?

Tracklist: 01-Being With You 02-The Tracks Of My Tears 03-I Second That Emotion 04-(Come 'Round Here) I'm The One You Need 05-Mickey's Monkey 06-Going To A Go-Go 07-I Don't Blame You At All 08-If You Can Want 09-Just To See Her 10-More Love 11-Just My Soul Responding 12-The Tears Of A Clown 13-Abraham, Martin And John 14-You've Really Got A Hod On Me 15-Shop Around 16-What's So Good About Goodbye 17-Ooo Baby Baby 18-The Love I Saw In You Was Just A Mirage 19-Quiet Storm 20-One Heartbeat 21-Baby, Baby Don't Cry 22-Cruisin'. Smokey robinson discography torrent download.

Regards, Maxim. Maxim, Yes, 7911 supports SSH but it needs phoneload 9.2.1 in it to support it & at this moment the main issues is that it's not getting on to 9.2.1.

If you refer the for firmware release 9.2.1 it says, For all SCCP/SIP firmware upgrades from firmware release versions earlier than 8.3(3) to version 9.2(1) or greater, you must first upgrade your firmware to an intermediate version (8.3(3) - 8.5(2)) then upgrade to 9.2(1). Therefore, as Paolo mentioned, you might want to upload the phoneload first to mentioned 8.x version on to your CUCM 8.6.2 ( which comes by default with 9.2.1 phoneload for 7911s ) & then once the 7911 gets 8.x phoneload, you may just change the device default value to 9.2.1 & bring them up to the mark as of others. Let us know how it goes. Pls rate the post if it helps. Maxim, Yes, 7911 supports SSH but it needs phoneload 9.2.1 in it to support it & at this moment the main issues is that it's not getting on to 9.2.1. If you refer the for firmware release 9.2.1 it says, For all SCCP/SIP firmware upgrades from firmware release versions earlier than 8.3(3) to version 9.2(1) or greater, you must first upgrade your firmware to an intermediate version (8.3(3) - 8.5(2)) then upgrade to 9.2(1). Therefore, as Paolo mentioned, you might want to upload the phoneload first to mentioned 8.x version on to your CUCM 8.6.2 ( which comes by default with 9.2.1 phoneload for 7911s ) & then once the 7911 gets 8.x phoneload, you may just change the device default value to 9.2.1 & bring them up to the mark as of others.